Re: Booting from SSD with a pre-UEFI bios

Posted on 2024-02-28, 17:43

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

BTW on another note - I wasn't able to get the PC to post for a while, turns out the problem was the GPU. It's a GTX 750 Ti, which came out in 2014. Think with some drivers I'll be able to get it to run? I'm not after optimal results, no bottlenecking etc, just so it runs and outputs video. Do you …

---

Re: Dual boot with Win 95 Dos and Win 3.11

Posted on 2024-02-23, 15:37

by

by AlaricD

in Windows

in Windows

Win95B (and all later Versions of Windows) supports FAT32, Win95A does not. A little nitpicking here, but: The original version of Win95 is not Win95A. Win95 is the original, Win95A is OSR1 (and included IE2.0); Win95B is OSR2. You are correct that Win95B supports FAT32 unlike its predecessors. …

---

Re: What game are you playing now?

Posted on 2024-02-22, 16:00

by

by AlaricD

in Milliways

in Milliways

I've been playing the heck out of Final Fantasy Renaissance lately. With the new jobs and items/weapons/armor, it feels so much fresher.

---

Re: Ti- Texas Instruments topic - list your product you have in your collection!

Posted on 2023-05-16, 19:54

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Just a few TI486SXL-40 (PGA132) CPUs. And, of course, calculators like those in the TI-8x series.

---

Re: What DOS games are there that support two simultaneous joysticks?

Posted on 2023-04-27, 19:04

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

What is the difference between using two dedicated ports versus a Y cable? How can try joysticks work off of the same port? One uses two dedicated ports, and the other uses a Y cable. Two joysticks can work off the same port (with the Y cable) because the 15-pin DSUB connector is a 15-pin DSUB …

---

Re: Troubleshooting 16MB, 30-pin SIMMs on M-321 board

Posted on 2023-01-24, 22:25

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

or if Address 11 or Data 7 are not connected somewhere That's actually quite likely... Do a diode check with a multimeter (the cheapest 5$ Aliexpress / Poundland / whatever model will do), putting red at A11 and black at +5V, and a second check putting black at A11 and red at GND. If neither of …

---

Re: Troubleshooting 16MB, 30-pin SIMMs on M-321 board

Posted on 2023-01-24, 22:21

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Do you have an eeprom burner? You may try Mr BIOS That's another idea. I've also found some additional M321 BIOS .BIN files. I *might* be able to scrounge up an EEPROM burner-- I have a friend with one but he hasn't seen it in ages so it's probably buried under anything/everything right now. I …

---

Re: Troubleshooting 16MB, 30-pin SIMMs on M-321 board

Posted on 2023-01-24, 20:24

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

BIOS chip marked: "386DX C1216 (C) 1989 AMI All Rights Reserved 386DX BIOS (Ver. 2.11)" Chipset has the PC Chips "CHIP 5": 4L04F1282, Japan 9306EAI "CHIP 6": 4L04F1666, Japan 9304EAI I'll update with the BIOS ID string just in case the markings on the BIOS chip don't reflect the actual BIOS. I …

---

Troubleshooting 16MB, 30-pin SIMMs on M-321 board

Posted on 2023-01-24, 18:14

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I have an M-321 rev 2.6 (or 2.7?) board and recently acquired four 30-pin, 16MB SIMMs, hoping to bring it up to 64MB or potentially 80MB by having four 4MB SIMMs in the other bank, but the RAM counts up to only 16000 bytes with those 16MB SIMMs in either Bank 0 or Bank 1 and the other bank left …

---

Re: Changing the PATH from the command line?

Posted on 2023-01-21, 23:33

by

by AlaricD

in DOS

in DOS

Use *SET*: SET PATH=%PATH%;C:\MASM

---

Re: How do I set up a CDrom in MSDOS 6.22?

Posted on 2023-01-13, 22:43

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Make sure VIDE-CDD.SYS looks for the drive on the right IRQ and port, so be sure you're setting the /P switch for that driver line correctly: /P:168,10 . CDSETUP just activates the IDE port, VIDE-CDD.SYS then looks for a CDROM drive attached to the port you tell it to look. https://www.vogonswiki. …

---

Re: Pc won’t read cd or disks

Posted on 2023-01-04, 21:01

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

You haven't specifically said if the drive is assigned a letter in DOS. For a CD-ROM drive, it's not enough that the BIOS enumerates it-- it needs a device driver (such as SBIDE.SYS or CDMKE.SYS or any number of others depending on drive) and a network redirector (the latter typically being MSCDEX. …

---

Re: Screensaver help

Posted on 2022-11-22, 21:24

by

by AlaricD

in Windows

in Windows

You may need to register the .DLL by opening an elevated command prompt, changing to the \windows\system32 directory and then issuing the command regsvr32.exe /r dllfilename.dll But if it's not a 32-bit .DLL, it probably won't be able to be loaded because of the removal of the 16-bit subsystem.

---

Re: your last purchased retro graphics card or any of your collection

Posted on 2022-11-15, 16:22

by

by AlaricD

in Marvin \ Video

in Marvin \ Video

ET4000/W32i, 2MB (although 1MB of it is 60ns instead of 45ns, so it sparkles quite a bit in the Doom timedemo). Used with my M-321 with Am38DX-40/Cx387DX-40, 256KB cache, and 32MB of RAM.

---

Re: Getting 387sx coprocessor working.

Posted on 2022-11-11, 18:45

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

From the collecting point of view 386sx is interesting to me as "a last 16 bit x86 cpu". I read somewhere it really is 32bits internally, but with only 16 bits exposed. This makes no sense to me at all. If it really is 32 bits internally than what is the difference between 386sx and 386dx? Just the …

---

Re: Getting 387sx coprocessor working.

Posted on 2022-11-11, 18:34

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

I honestly never understood the point of the 387sx The point of the 387 (whether S X or D X is to provide floating point operation to the system. All it does is floating point; it does not replace the 386 itself. Are you thinking of the 486SX/487SX (in which the 487SX is just a 486DX that takes …

---

Re: Ehy guys, what is this? AMD 386 40MHZ, Cyrix co-processor, 8MB RAM...

Posted on 2022-08-31, 15:47

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Throw on a graphics card to see if that helps-- it's not going to boot very far without a graphics card.

---

Re: olivetti pcs 86

Posted on 2022-08-22, 14:24

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

scroeffie wrote on 2022-08-22, 14:09: i have 30p sim mem they dont fit they are to long ! iam impressed with the games that it can run on 30-pin SIMMs are 30-pin SIMMs. Make sure you're not inserting them backwards.

---

Re: First Time User of DOSBox

Posted on 2022-07-13, 16:44

by

by AlaricD

in DOSBox General

in DOSBox General

The D: drive *SHOULD* be accessible and have the actual files (including any .EXE) in it. If D: still shows a .BIN and .CUE as contents, there's something weird going on.

---

Re: What old hardware you own is yet not found a better modern equivalent ?

Posted on 2022-06-30, 14:48

by

by AlaricD

in Marvin \ General Old Hardware

in Marvin \ General Old Hardware

Joseph_Joestar wrote on 2022-06-30, 14:20: On that note, Digital Foundry has a video showcasing how even modern games can look great on a hi-end CRT monitor. Which, if watched on an LCD display, tells you nothing about the picture quality.

---